Great Printer. Great Price! I had it put together in a few hours and after reading about leveling the bed, I had a Benchy going and it failed about half way thru the print. One of the bolts came undo on the effector and the hot end crashed into the print. I put some loc-tite on all the bolts, tightened them all up and did 20 hours of printing with no failures. Now I'm waiting to install the Wham-Bam Build Plate and this will be my go-to printer for big things. I would highly recommend this to anyone as a second printer. Not a first, because of the assembly, but if you are a tinker-type person, definitely get this printer.

Printer is so much better now with the auto level added to it. It is ridiculously good once you proper simple tune ups. I have two of anycubic deltas. Recommended things to do to your anycubic printer which I recommend Anycubic to look into providing some or all of these things: Getting better stepper motors will quiet the printer considerably and give better prints (the default ones are fine but if you want better). Corner braces and a better fan duct which can be 3d printed. Also check the printer overall to make sure everything is properly secured. I have used a thin sheet of rigid transparent plastic packaging as a shim between the arm carriage and linear rail bracket because I notice a bit of wobble even though the screws were firmly secured. The printer has been printing great since. I thought about making a video about it.

This was my first DIY kit and my first delta printer. The build was very easy and the instructions were spot on accurate. Started printing with benchy and a calibration cube, and they printed perfect the first try. The issues I had was with auto bed leveling it works great but after a few prints it seems to forget the bed level on the next print. Its random at the start of a print. So I have to run the bed leveling all over again. Minor issue as it does keep it leveled. Overall it's a great printer for a steal. $225 for this is a no brainers and I would purchase again. I'm already considering it for a second one as I am addicted to printing

Excellent printer for the money, and awesome customer service.

Overall this printer works very well with the stock setup. The frame wobbles from quick movements of the effector, and that introduces ringing or ghosting artifacts into your prints, but that is easily fixed by printing some braces or slowing down your print speeds. The printer firmware is available from the Anycubic website, but really should be distributed on the SD card in order to be compliant with the open source license.



My one complaint is that I asked for the US power cord and got the EU version. I had a spare laying around, but it appears I'm not the only one this happened to, so I think whoever is shipping these out needs to be more careful.

Great customer service very helpful and responsive. firmware little bit of a hassle could improve other than that great product very pleased would recommend

AnyCubic Kossel plus - I am very happy with the overall value (quality/price). I went against the advice of many and selected this as my first 3D printer. I am very happy with it. Minor problem that they sent the wrong power cord (European but I'm in US). However, it is a standard computer power cable so this was easy to resolve. No scratches or dings from shipping. Very easy to build just from watching their online assembly video. I did update to the latest 8bit Marlin firmware (1.1.9). Auto calibration and bed leveling using included probe is excellent. Full reel of white filament is an awesome bonus, I was able to start printing right away. Print quality has been excellent.

I am happy with each of the prints I have made so far... There are so few quality issues that I couldn't believe that I could actually afford such a well tuned machine. There are a few things that are not noted in the instructions, however. There were black pins in the vertical frames that MUST be pulled out prior to operation. If not the machine will run the arms into them instead of it's limit switches. Also, one of the SD cards did not work. Like it wasn't even formatted. But in spite of these few problems, this machine rocks five stars for this novice printer operator.

very happy with the build quality of the frame and design, but disappointed with the quality of the hot end after only two prints the thermistor came adrift from the heat block it is a very cheap way of holding the thermistor in place its not held by a screw in terminal only pushed in other than that it went together and setup with little problem.

this is of course not the problem of the seller who has given superb service and I would use again without hesitation

Awesome Company to order from even with their new year going on I received my printer pretty quick. I am still assembling the printer making changes as I go per suggestions from others on Facebook & yahoo. All parts as described & manual is very easy to understand. I would recommend this company to everyone looking for good service.

Great customer service. Had some concerns with shipping and was immediately reassured my printer would be shipped asap. Printer arrived in a timely manner and everything I needed to assemble was provided. I did not assemble it. My son assembled it as he has the same printer. He had no problems. I have only done a few small projects and so far no issues. So far I am very pleased with this printer.

Only used for a couple small experimental jobs so far, but seems to be dialing in. Assembly instructions are good enough, but setup/operational instructions are non existent. I think it's a good machine but not the easiest for a rookie.

The kit was complete and came together easily. I attempted a print on the stock firmware which failed so I upgraded to Marlin 1.1.9 and found a good auto leveling mod online. Now it prints reliably. I have used speeds up to 150mm/s successfully! That was my major need for a delta style. I might try even faster as I upgrade the parts.

Very quick delivery, very helpful folks correcting a mistake I made in my order. Printer assembled easily, and prints well with stock firmware.

This was my first 3D printer. The shipping and package were great! Everything was packed up in a small bags and the manual is pretty detailed. Some pictures are not up-to-date as on the photos were older version of some parts. Even with this it was quite easy to follow. I was able to build the printer in less than 4 hours. Once it was assembled I level up the bed with the leveling probe and start printing. Even the first model was good quality. I needed to adjust the Z- offset so the first layer was properly placed. Up to now I have around 10 models printed with no issues.

I would recommend this printer and 3dprintersbay.com to any of my friends.