Had this printer for nearly a year now and still going good so far. Setup was pretty straight forward, just follow the steps and make sure everything is done up/tight enough and you’ll be ok.



If your prints don’t stick after a few prints, clean the bed with windex, seems to make my prints stick nicely then, especially when building with a raft support.



In response to someone else’s review here about the intermittent beeps during print, put a small amount of cooking oil/lubricant on the Filaments spindle/holder using your finger or ear bud, the beeps usually occur when the filament roll spins and encounters some friction on the handle that you mount it on. The filament sensor detects a stoppage for a split moment thus beeping, the oil fixes the problem and makes the roll spin easily! Worked for me, try it out if it happens to you.

The only problem I’ve had with it so far is not being able to control the e-steps. But given the track record with 3-D Printers Bay, I expect to have an answer before long. Simply because their Customer service.Their responsiveness to my never ending questions has been second to none.

As for the printer, it is awesome. Blazing fast and freakishly accurate compared to my current experience with 3-D printing. I’ve had some trouble getting it to connect with my computer, and like I said before with the Eastep’s, the closed firmware is annoying. But it is such a solid printer there’s very little I actually need to change. Great for beginners, maybe not so great for the advanced who like to tinker programming.

Ordered this during the extended holiday, and Honestly I couldnt be happier with the purchase. Yes it took it a bit of time to recieve it (direct from manufacture) but it was 100% worth it and it prints like a dream. If you are having issues with the bed not being level then heat it up to 80° with the bed screws loose and let the bed heat soak for a few minuits then while it is still hot tighten them down, and that should solve the issue. there are many modifications also from increasing the build height to enclosures and effector as well. Glad I got this over the TLM!

Finally this weekend I could have time to assemble this HUGE printer, and after a couple of hours, (I take my ti study and check how is made and the quality of the components), I start printing without any important issue (still improving my config in simplify3d). Very happy with this printer, has a lot of.potential, and could be tuned in so many ways, I recommend 100%,, good quality for the price, and thinking to buy another one

Stampante assolutamente gigante come visto in moltissimi video su YouTube, facile da assemblare completa tutti gli accessori per il montaggio e molti componenti di ricambio già nella confezione, ad esempio 2 aste i carbonio, ugelli, hotehad,1 kg di pla ed alcuni colori di pla omaggio.

La stampante una volta assemblata con un ottimo manuale in inglese ma con immagini assolutamente esplicative,risulta facilissima da impostare, io ho stampato 30 min dopo il termine della messa a punto è della calibrazione automatica, completamente spiegata nel manuale, il display touch assolutamente perfetto.

Cosa dire ? Sono contentissimo di aver acquistato la mia prima stampante Delta e che sia stata questa Anycubic Predator

Semplicemente bellissima da usare, da vedere, assolutamente consigliatissima

Spedizione velocissima dalla Germania

It's very sturdy and well built, the printing right out of box is amazing,I love it what anycubic needs is to open source their board's and to make it people friendly, and put profiles for cura,with all that being said yes buy their predator, I now have two

I received my Predator 2 weeks ago almost. Very satisfied about product and 3DPrintersBay, you guys do a really good job and your customer service on Facebook is awesome. Very good job and thank you so much

After nearly 2 weeks I still love mine.

It has changed my whole 3DP outlook,

which now feels as though 3DP become easy to do.

The Predator is like and appliance, just switch it on and use it.

No hair spray, no glue, no mess.

No leveling issues.

And It's whisper quiet.

My only serious cons are ....

I would like to see a better SD card slot.

And that display/panel needs some sensitivity training.

This printer is pretty awesome. with less that an hour for the build, it was printing without issue. It has multiple spare parts which is awesome. And the printing size is huge for a delta. I'm printing easily at 80-100mm/sec even on a benchy with great result. Thanks for a great printer

I've owned this printer for about three weeks now. I have enjoyed it very much. My thoughts:



Pros:

Very quiet printer

Good print speed

Good accuracy

Ultrabase makes print removal easy when it's maintained properly

Great build volume for the price point

Handles typical PLA filaments very well



Cons:

Intermittent beeping during prints that I have not been able to determine the cause of.

Potential mod issues due to mainboard.

Touch pad, even after calibrating, does not register touch inputs very well, which gets annoying when walking the printhead down during z-height calibration.

Stock extruder has a difficult time with exotics like woodfill, modifying to an aftermarket extruder takes a little creativity and research.



Overall, I would highly recommend purchasing this printer.

I am very pleased with this printer.

Thank you so much.

The printer is pretty good, easy to assemble. Quality price is excellent. My main complain is that the printing height is not 455mm as advertised, more around 400-410. Got a failure after 4 days of printing as one of the arms reached the top. Besides that, is a very good product quite painless to setup and use.

This printer is such a good value that I ordered five more. Thanks AnyCubic!

It's a good solid workhorse machine. I had it printing four parts over a week continuously, and I never had to relevel or fiddle with it much. Had to do quite a bit of calibration for the cura profile and testing before that, but that is true of all printers.

Took me 55 minutes to be unboxed, assembled, and doing the level test.



My first impression is that this is really a deluxe kit. It has two extra arms, an extra hot end, extra nozzles, and nice tools that go beyond the basics, like flush cutters and nozzle uncloggers. Plus a full roll of filament and then some smaller quantities of color samples.