Estimate Shipping cost
Folger Tech Cloner 3D Printer Kit
FREE Shipping to United States.
** As we receive customer feedback we do make small alterations to the kit if we feel they improve the kits performance and stability, the kit you receive might reflect some of these slight changes and improvements.
The Folger Technologies Cloner is a great kit combining the simplicity of an erector set with the power of a much more expensive desktop printer. The kit comes with everything you need to assemble the machine With the use of a few simple tools and a little bit of time you too can get started 3D printing the worlds next big idea
This kit is a remake of a common open source design that has been improved and made more DIY/Maker friendly using the RAMPS controller with Marlin, and the 2004 LCD with SD card for standalone printing with out the PC.
Buyer Protection Policies
PayPal-the most reliable payment method.Credit/Debit cards processed by PayPal
USPS(US)/UPS(Outside US) Insured Shipment
High Quality Express Transport without damage.
1 Year Warranty
Just in case. Of course we only ship out perfect products.
Technical Support Service
Experiencing trouble? Feel free to contact us!
Complete Set of Black Injections Molded Parts
2004 LCD with SD card Reader
Laser cut Frame (Melamine or Oak) [Made in the USA]
x8 LM8SUU Linear Bearings
x2 SC8LUU Bearings (Bed)
x4 MP105 bearings
x1 Idler Pulley
8mm Chromed Linear Rod for X, Y, Z (Pre-Cut)
T8 Lead Screw 2mm pitch
x1 230mmx150mm Heat Bed
x1 Direct Drive Extruder w/ Injection Molded Parts for 1.75mm ABS/PLA/Wood/HIPS/PETG (Available in Dual or Single Extruders)
360W 12v 30A Power Supply
x4 NEMA 17 2.6kg/cm Stepper Motors
x1 NEMA 17 4.8kg/cm Stepper Motor (Used for Bed)
x3 Meters of GT2 Belt
x1 GT2-188 Belt
x6 20 Tooth Pulleys
x1 36 Tooth Pulleys
x1 Ramps 1.4
x1 Arduino Mega 2560 R3 Clone
x5 A4988 Stepper Drivers
x1 Roll of 8mm Kapton Tape
x2 5mmx8mm Couplings
x3 Electronic End Stop Circuits w/ LED
x3 Belt Tensioners
x4 Threaded Bed Adjustment Knobs
x4 Bed Springs
All Required Nuts/Bolts for Assembly
Impressive 230mmx150mmx120mm Build Area
Able to print ABS & PLA Plastic (1.75mm)
Can run 110V or 220V (Only Comes With US Cord)
Items you will need:
Build Guide / Firmware and Software
This is a kit of components for assembly into a 3D Printer by the end user. Building and using the printer is potentially very dangerous as it involves electricity and high temperatures.
Building the printer will require a certain amount of physical dexterity, common sense and a thorough understanding of what you are doing. We have provided fully comprehensive build documentation to enable you to build your Folger Tech 3D Printer Kit in a safe manner.
However ultimately we cannot be responsible for your health and safety whilst building or operating the printer, with that in mind be sure you are confident with what you are doing prior to commencing with building or buying. Read all of the manual to enable you to make an informed decision.
Building and operating involves electricity, so all necessary precautions should be taken and adhered to, the printer runs on 12V supplied by a certified power supply, so you shouldn't ever have to get involved with anything over 12V but bear in mind there can still be high currents involved and even at 12V they shouldn't be taken lightly.
High temperatures are involved with 3D Printing, the Extrusion nozzle of the hot end runs at 230°C, the heated bed runs a 110°C and the molten plastic extruded will initially be at around 200°C, so special care and attention should be made when handling these parts of the printer during operation.
We wouldn't recommend leaving your printer running unattended.We cannot be held responsible for any loss, damage, threat, hurt or other negligent result from either building or using the printer
Folger Tech Cloner 3D Printer Kit
Credit Cards processed by Secure PayPal Gateway
- Order Fulfillment by : FOLGERTECH
- Product Code:
- Availability: Out Of Stock