Folger Tech RepRap Prusa i3 Clear Frame Full 3D Printer Kit

Dispatch time:Ships in 1-2 Business days

FREE Shipping to United States.

Other items you might be interested in buying with your kit:

2004 LCD Controller w/ SD Card Reader (Print Without a Computer!) ($12)

LCD screen with adapter for RAMPS 1.4 controller board. Includes SD card reader, buzzer, stop button, and turnable knob that also acts as a button.

** Assembly required

** As we receive customer feedback we do make small alterations to the kit if we feel they improve the kits performance and stability, the kit you receive might reflect some of these slight changes and improvements.

The Folger Technologies Prusa i3 is a great beginner kit combining the simplicity of an erector set with the power of a much more expensive desktop printer. The kit comes with everything you need to assemble the machine (with the exception of an 8"x8" glass surface). With the use of a few simple tools and a little bit of time you too can get started 3D printing the worlds next big idea

  Buyer Protection Policies

This kit includes the following:

  Complete Set of Black Printed Plastic Parts. [Made in the USA]

  Clear Acrylic frame [Made in the USA]

  x12 LM8UU Linear Bearings (2 spares)

  x2 623ZZ Bearings

  8mm Stainless Steal Threaded Rod (Pre-Cut)

  8mm Chromed Linear Rod for X, Y, Z (Pre-Cut)

  5mm Threaded Rod 

  x1 Dual Power 12v/24v Heated Bed

  x1 Direct Drive Extruder w/ Injection Molded Parts for 1.75mm ABS/PLA Assembled in the USA

  360W 12v 30A Power Supply (Not Pictured)

  x4 NEMA 17 2.6kg/cm Stepper Motors

  x1 NEMA 17 4.8kg/cm Stepper Motor (Used for Bed)

  2 Meters of GT2 Belt

  x2 20 Tooth Pulleys

  x1 Ramps 1.4

  x1 Arduino Mega 2560 R3 Clone

  x5 A4988 Stepper Drivers (1 Extra)

  x1 Roll of 8mm Kapton Tape

  x2 5mmx5mm Couplings

  x3 Electronic End Stop Circuits w/ LED

  x2 Belt Tensioners

  x4 Threaded Bed Adjustment Knobs

  x4 Bed Springs

  All Required Nuts/Bolts for Assembly

  Power Cable

Features:

  Impressive 8”x8”x7” Build Area

  Able to print ABS & PLA Plastic (1.75mm)

  Can run 110V or 220V (Only Comes With US Cord)

Items you will need:

  Tools

  Filament

  8x8 Glass Print Area (Lowes or Home Depot)

  Time

Build Guide / Firmware and Software

Google Drive link

Disclaimer:

This is a kit of components for assembly into a 3D Printer by the end user. Building and using the printer is potentially very dangerous as it involves electricity and high temperatures.

Building the printer will require a certain amount of physical dexterity, common sense and a thorough understanding of what you are doing. We have provided fully comprehensive build documentation to enable you to build your Folger Tech 3D Printer Kit in a safe manner.

However ultimately we cannot be responsible for your health and safety whilst building or operating the printer, with that in mind be sure you are confident with what you are doing prior to commencing with building or buying. Read all of the manual to enable you to make an informed decision. 

Building and operating involves electricity, so all necessary precautions should be taken and adhered to, the printer runs on 12V supplied by a certified power supply, so you shouldn't ever have to get involved with anything over 12V but bear in mind there can still be high currents involved and even at 12V they shouldn't be taken lightly. 

High temperatures are involved with 3D Printing, the Extrusion nozzle of the hot end runs at 230°C, the heated bed runs a 110°C and the molten plastic extruded will initially be at around 200°C, so special care and attention should be made when handling these parts of the printer during operation. 

We wouldn't recommend leaving your printer running unattended.We cannot be held responsible for any loss, damage, threat, hurt or other negligent result from either building or using the printer